Do you have a Ring Doorbell, but can’t seem to figure out how to put it back on after charging? Don’t worry, we’ve got you covered.
In this article, we’ll be taking a look at the steps you need to take to properly put your Ring Doorbell back on after charging.
We’ll be discussing how to charge your Ring Doorbell, how to remove and replace the battery, and how to reattach it to the mounting bracket.
Finally, we’ll provide some troubleshooting tips to help you if you run into any issues.
So, if you’re ready to get your Ring Doorbell back up and running, then let’s get started!
Table of Contents
Short Answer
To put your Ring Doorbell back on after charging, start by ensuring that the charging cable has been disconnected from the device.
Next, use the provided screws and mounting bracket to attach the device to an exterior wall.
Finally, once the device is securely mounted, press the orange button on the back of the device to power it on.
If you are having trouble, refer to the installation instructions provided with the device.
What Are the Steps to Put Ring Doorbell Back On?
Putting your Ring Doorbell back on after charging is a relatively simple process.
Before you start, make sure that your Ring Doorbell is fully charged.
This will ensure that its ready to go when youre ready to attach it back on the wall.
After youve confirmed that its charged, there are four easy steps to follow in order to get your doorbell back up and running.
The first step is to remove the battery.
Most Ring Doorbells come with removable batteries, so youll need to locate the battery compartment and remove the battery.
Be careful when removing the battery as it can be fragile.
The second step is to replace the battery securely.
Make sure that the battery is correctly seated in the compartment and that it is secure.
The third step is to reattach the doorbell to the mounting bracket.
Depending on the doorbell model, you may need to use the screws provided to secure the doorbell to the bracket.
Finally, the fourth step is to secure the doorbell to the bracket.
Make sure that the screws are tight and that the doorbell is securely attached to the bracket.
Once youve completed these steps, your Ring Doorbell should be back on and ready to go.
Following these steps will ensure that your Ring Doorbell is back on and functioning correctly.
Its also important to regularly check your doorbells battery level to make sure that it is charged and ready to go at all times.
With a well-maintained Ring Doorbell, you can always count on it to keep your home safe and secure.
Step 1
Putting your Ring Doorbell back on after charging is an easy process that will only take a few minutes of your time.
The first step is to make sure your Ring Doorbell is fully charged.
This can be done by using the included USB charger and plugging it into a nearby power source.
Once the charging indicator light turns green, it is safe to assume that your Ring Doorbell is at its full capacity and ready to be put back on the wall.
To check the charge level of your Ring Doorbell, you can use the Ring app, where you will be able to view the battery percentage.
Additionally, you can also press and hold the doorbells button for three seconds to view the current charge level.
It is important to make sure that your Ring Doorbell is sufficiently charged before attempting to put it back on the wall.
If the charge level is too low, the doorbell may not be able to connect to the internet and will need to be charged again.
Additionally, low battery levels could cause the doorbell to disconnect or malfunction, so it is essential to ensure the battery is at its optimal level before putting it back on the wall.
Step 2
Once the Ring Doorbell has been fully charged, its time to remove the battery and replace it securely.
The battery is located at the back of the device, and it should easily pop out.
Make sure to take note of the orientation of the battery before removing it, as putting it back in the wrong way can cause issues with the device.
If you are unsure, take a picture for reference.
Once you have the battery removed, its time to put it back in.
Insert the battery into the slot and make sure its secure.
You can use the provided screws to make sure the battery is in place.
Its important to make sure the battery is in the right way, as previously mentioned.
Once youve done that, you can move onto the next step.
Step 3
Once the battery is securely in place, the next step is to reattach the Ring Doorbell back to its mounting bracket.
Depending on the model of Ring Doorbell you have, it may be necessary to use the screws provided for this step.
If your Ring Doorbell has a mounting bracket that requires screws, it is important to make sure that the screws are tight enough to hold the device securely in place.
It is also important to make sure that the screws are not over-tightened, as this can cause damage to the device.
Once the Ring Doorbell is securely in place, it is important to check the alignment of the device.
This can be done by looking at the image shown on the screen to ensure that the motion sensor is pointing in the right direction.
This will ensure that the device is able to detect motion accurately.
After these steps are taken, your Ring Doorbell should be back on and functioning properly.
It is important to make sure that the device is secure and functioning correctly, as this will ensure that you can get the full benefit of the device.
As long as the device is securely mounted and the battery is charged, you should have no problems with your Ring Doorbell.
Step 4
Once the battery has been replaced and the doorbell is securely back in its mounting bracket, the final step is to make sure that the device is secured with the screws provided.
This may seem like a small step, but it is actually one of the most important when it comes to ensuring that your Ring Doorbell is back on and functioning correctly after charging.
The screws provided by Ring are specifically designed for the doorbell and its mounting bracket.
Tightening them correctly will help to ensure that the device is securely fastened to the wall or other surface, as well as providing a water-tight seal.
This is important to prevent any moisture from entering the device and potentially causing damage.
In order to securely fasten your Ring Doorbell, it is important to use the provided screws and to tighten them firmly but not too tightly.
If the screws are over-tightened, this could damage the device or even cause it to become loose over time.
It is also important to ensure that the screws are fully inserted into the wall so that the device is properly secured in place.
Once the screws are firmly secured, your Ring Doorbell is now back on and ready to be used.
With a few simple steps, you can now have the peace of mind that your Ring Doorbell is securely in place and working correctly.
Step 5
The final step in putting your Ring Doorbell back on after charging is to reattach it to its mounting bracket and secure it with the screws provided.
This is an important step that should not be overlooked as it ensures that your Ring Doorbell is securely mounted and will remain in place after it is powered up.
To attach your Ring Doorbell to its mounting bracket, first make sure that the mounting bracket is securely affixed to the wall or other surface.
Then, line up the holes on the back of the Ring Doorbell with the holes on the mounting bracket.
Insert the screws provided into the holes and tighten with a screwdriver.
Make sure that the screws are tightened securely to ensure a firm connection.
Once the mounting bracket is secure, carefully place your Ring Doorbell onto the bracket and press down firmly until it clicks into place.
Check to make sure that the connection is secure and that the Ring Doorbell is securely mounted to the bracket.
Thats it! Your Ring Doorbell is now back on and ready to be used.
Following these steps will ensure that your Ring Doorbell is securely mounted and will remain in place after it is powered up.
Troubleshooting Tips
Troubleshooting your Ring Doorbell after charging can be a tricky process. Depending on the model of your doorbell, you may need to take a few extra steps to make sure it functions correctly. Here are a few tips to help you troubleshoot:
1. Make sure that your Ring Doorbell is fully charged before attempting to reattach it. Check the power indicator light to ensure that the battery is fully charged.
2. Make sure that the mounting bracket is secure and level before attempting to reattach the doorbell. Check all of the screws and tighten any that may have become loose.
3. If your Ring Doorbell has a removable battery, make sure to remove it and replace it securely. This will ensure that the device is able to power up correctly.
4. Make sure that the doorbell is firmly attached to its mounting bracket before securing it with the screws provided.
5. If your Ring Doorbell is still not functioning correctly after following the above steps, you may need to contact customer support or take it in for repair.
Following these tips should help you get your Ring Doorbell back up and running correctly.
If you are still having difficulties, contact customer support for further assistance.
Final Thoughts
By following the steps outlined above, you can easily put your Ring Doorbell back on after it has been charged.
Making sure that your Ring Doorbell is properly secured and functioning correctly is key to ensuring your home’s security.
So, take the time to double check that your Ring Doorbell is securely attached to the mounting bracket and that it is functioning properly.
Doing so will give you peace of mind knowing your home is safe and secure.