Do you want to remove your Ring Video Doorbell Pro Faceplate? If so, then youve come to the right place.
In this step-by-step guide, we will show you exactly how to do it.
We will cover what youll need to get started, how to locate the release tab, unlocking the faceplate, pulling it away from the mounting bracket, disconnecting the wiring, removing the faceplate, and finally, reconnecting the wiring.
So, lets get started!
Table of Contents
Short Answer
To remove the ring video doorbell pro faceplate, first, press and hold the release button.
Then, use a flat-head screwdriver to lift the faceplate off the device.
Next, disconnect the wires from the device and remove the faceplate.
Finally, reattach the wires to the device and put the faceplate back on, pressing firmly until it clicks into place.
What You’ll Need
Removing the faceplate from your Ring Video Doorbell Pro is a straightforward process, but it does require a few items to make it easier.
First, you’ll need a flat-head screwdriver to press the release tab on the bottom of the faceplate and unlock it.
You’ll also need a pair of wire cutters or needle-nose pliers to disconnect the wiring, if necessary.
Finally, you’ll need a Phillips head screwdriver to remove the faceplate from the mounting bracket, if necessary.
It’s always a good idea to have these items handy when removing the Ring Video Doorbell Pro faceplate.
Locating the Release Tab
Finding the release tab on the bottom of the Ring Video Doorbell Pro faceplate is the first step in removing the faceplate.
The tab is usually located on the bottom side of the faceplate and is clearly marked with the word release or a corresponding icon.
It is important to make sure that you are pressing the right tab, as there are several small tabs on the faceplate and they all serve different purposes.
Once you have located the release tab, press it firmly to unlock the faceplate.
Depending on the model of the doorbell, you may need to press and hold the tab for a few seconds before it unlocks.
You should hear a slight click when the faceplate is unlocked.
Unlocking the Faceplate
When you have located the release tab on the bottom of the faceplate, press it to unlock the faceplate.
It is important to note that different models of the Ring Video Doorbell Pro may have different release tabs, so you may need to consult your manual to ensure you are pressing the correct button.
Once the faceplate is unlocked, you can easily pull it away from the mounting bracket and disconnect the wiring.
Be sure to take extra care when disconnecting the wiring, as it is delicate and can be easily damaged.
Be sure to keep all the parts together, as you will need them to re-attach the faceplate.
Once the wiring has been disconnected, you can easily remove the faceplate from the device.
Pulling the Faceplate Away from the Mounting Bracket
Removing the Ring Video Doorbell Pro’s faceplate is an easy process that only takes a few minutes.
The first step is to locate the release tab on the bottom of the faceplate.
This tab is usually located near the bottom of the faceplate, and can be easily identified by its distinct shape and color.
Once you have found the tab, press it to unlock the faceplate from the mounting bracket.
Once the faceplate is unlocked, you can then pull the faceplate away from the mounting bracket.
The faceplate should slide off with ease, although you may need to use a bit of force if the fit is tight.
Once the faceplate is completely detached from the mounting bracket, you can then disconnect the wiring.
Make sure to take note of the wiring configuration before disconnecting, so you can reattach it in the same position when re-installing the faceplate.
Once the wiring is disconnected, you can easily remove the faceplate from the device.
At this point, you can proceed to clean the faceplate or replace it with a new one, depending on the desired outcome.
Be sure to take care when re-installing the faceplate, so as not to damage any of the components.
It is also important to ensure that the wiring is connected properly, and that the faceplate is firmly secured back onto the mounting bracket.
Disconnecting the Wiring
When it comes to removing the faceplate from your Ring Video Doorbell Pro, the final step is disconnecting the wiring.
This is an important step because it ensures that the device is safely disconnected from the power source.
To do this, locate the release tab on the bottom of the faceplate and press it to unlock the faceplate.
This will allow you to pull the faceplate away from the mounting bracket.
Once you have done so, you can safely disconnect the wiring.
Depending on the type of wiring you have, this can involve unscrewing the connections or simply unplugging them.
If youre unfamiliar with the wiring, its best to consult the user manual or contact customer service for assistance.
Once the wiring is disconnected, you can easily remove the faceplate from the device.
Removing the Faceplate
Removing the faceplate from your Ring Video Doorbell Pro is a simple process that only takes a few minutes.
To get started, you’ll need to locate the release tab on the bottom of the faceplate.
This tab is located at the bottom of the faceplate and will allow you to unlock the faceplate once it has been pressed.
Once the tab has been pressed and the faceplate is unlocked, you can easily pull the faceplate away from the mounting bracket and disconnect the wiring.
After that, you can safely remove the faceplate from the device.
It’s important to note that you should unplug the device from the power source before attempting to remove the faceplate.
This will prevent any potential damage from occurring due to electrical shock.
Additionally, you’ll want to make sure that the release tab is properly pressed before trying to pull the faceplate away from the mounting bracket.
If the release tab is not pressed properly, you may end up damaging the device.
Once the faceplate has been removed, you can inspect the wiring to make sure everything is connected correctly.
Additionally, you can check the faceplate for any signs of damage or wear and tear and replace it if necessary.
Once the inspection is complete, you can securely reattach the faceplate to the device using the mounting bracket and reattach the wiring.
Then, you can plug the device back into the power source and you’re good to go!
Reconnecting the Wiring
Reconnecting the wiring on your Ring Video Doorbell Pro is a straightforward process.
First, youll need to locate the two wires connected to the faceplate.
Once you have located the wires, the next step is to remove the wire nuts from the wires that attach them to the faceplate.
After that, you can disconnect the wires from the faceplate.
Once the wires are disconnected, you can then reconnect them to the mounting bracket.
Finally, once all of the wires are connected securely, you can slide the faceplate back into the mounting bracket and replace the wire nuts to secure the wires.
This will ensure that the wiring is secure and your Ring Video Doorbell Pro is ready to use.
Final Thoughts
With just a few simple steps, you can easily remove the faceplate from your Ring Video Doorbell Pro.
All you need is a few minutes of your time and the necessary tools.
Now that you know how to remove the faceplate, why not take the time to do it and keep your device in tip-top shape?